Drivers restriction:

Modified Drivers NOT allowed in this class.

Chassis:

Kyosho Mini-Z Racer MR01, MR015, MR02, MR03, PN Racing PNR2.5W.

90mm - 102mm wheelbase.

Body:

Kyosho Mini-Z, TRP Scale and Jomurema GT01 body only, Le Mans body on 102mm cars, full windshield and window must be installed, Lexan window and Lexan Roof allowed.

Motor:

Kyosho MZ9P Motor from RTR. Any 3500kv brushless motor, option PN Armature allowed.

PN 70 Turn brushed motor, The motors are to be run as is.

Gear Ratio:

No Restrictions

ESC:

Kyosho RTR board, Kyosho EVO board, PN Racing DSM2 board or PN Racing V2 16A ESC.

Battery:

Cars must be powered by four AAA Ni-MH, Ni-Cd or alkaline batteries only.

Wheels:

All brand Plastic and Aluminum Mini-Z production wheel rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 20mm. Offset must fit inside the body.

Tire:

Any brand rubber Mini-Z production tires allowed. Foam or silicone tires and traction compounds not allowed.

Upgrades:

Any aftermarket brand Mini-Z production parts and upgrades allowed.

Chassis:

Any 2wd, 90mm - 98mm wheelbase chassis.

Body:

Kyosho Mini-Z, TRP Scale and Jomurema GT01 body only, full windshield and window must be installed, Lexan window and Lexan Roof allowed. Lexan GT bodies allowed, No Le Mans bodies

Motor:

50 Turn brushed motor or 5600kv or below brushless motor, using AAA batteries.

70 Turn brushed motor or 3500kv brushless motor using LiFe/LiPo Batteries

Fixed Gear Ratio

64 pitch, 10 tooth pinion, 53 tooth spur. Must be (416410WC) and (MR2953WC)

48 pitch, 8 tooth pinion, 43 tooth spur.

ESC:

Any brushed or brushless ESC

Battery:

See motor specs

Wheels:

All brand Plastic and Aluminum Mini-Z production wheel rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 20mm. Offset must fit inside the body.

Tire:

Any brand rubber Mini-Z production tires allowed. Foam or silicone tires and traction compounds not allowed.

Option Parts:

Any aftermarket brand Mini-Z, GL Racing, RTRC, Nexx, or Atomic production parts and upgrades allowed.

Chassis:

Any 2wd, 90mm - 102mm wheelbase chassis.

Body:

Kyosho Mini-Z, TRP Scale and Jomurema GT01 body only, full windshield and window must be installed, Lexan window and Lexan Roof allowed. Lexan GT bodies allowed, Le Mans bodies allowed.

Motor:

Open, No Restriction

ESC:

Open any ESC

Battery:

Any battery, maximum 8.4 volt

Option Parts:

Any option parts

Wheels:

All brand Plastic and Aluminum Mini-Z production wheel rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 20mm. Offset must fit inside the body.

Tire:

Any brand rubber Mini-Z production tires allowed. Foam or silicone tires and traction compounds not allowed.

Driver restriction: No F1 Super Stock, Mod/Pan, class drivers allowed.

Motor:Kyosho MZ9P, or PN 70T motor only.

Chassis:Kyohso MR03S, MR03S2 and MR03 RWD.

Wheels:Any plastic wheels, Maximum front 8.5mm x 20mm, Maximum rear 11mm x 20mm, offset must fit inside of the body. Side wall disks not allowed.

Tire:Mini-Z rubber tires only, no silicone. Traction Compounds NOT allowed on tire or on race surface. Tires may be cleaned with a 70% alcohol solution

Electronics & Transmitter: Kyohso original from RTR, PN 70T motor, and PN replacement servo parts only.

Gear Ratio: Fixed 48 Pitch, 6T, 7T, 8T, or 9T Pinion with the Stock Kyosho Gear Diff.

Wheelbase: 90mm to 102mm

Body: Any hard body, limited wheel and top shock clearance modification allowed. Optional aftermarket wing is allowed. No lexan roofs or windows. Front splitters may be rounded.

Batteries: Any AAA NiMH, 4pcs only.

Option/Durability Parts Allowed: Must be these exact parts.

Any manufactures ball bearings, wheel nuts, T-Plates, springs, shims, motor wires, and screws are allowed.

MR3055 Teflon Ball King Pin Set

MR3046 Aluminum Low Down Knuckle

MR2060 Multi Length Disk Damper Set

MR3058A Brass Weight T-Bar Mount

MR2161 PN Racing Mini-Z MR02/03 Dual Spring Center Shock

BM001 Interchangeable Front Body Mount Base and corresponding carbon fiber body adaptor

Modifications: Only the king pin flip and authorized option parts listed above are allowed. King pins must be cut to prevent track damage if flipped. Car must be run in stock configuration other than those modifications.